
Hot & Cold Thermal Bags, Insulated Mailers & Cold Chain Delivery Packaging

Fertilizer, Pesticide & Agrochemical Packaging

Cleaner, Laundry & Air Care Packaging

Custom Medical Packaging Solutions

Protective Structures, Inserts and Retail Packs

Custom Protein Powder Pouches, Vitamin Stick Packs & Nutrition Bar Bags

Cosmetics, Fragrance and Skincare Packaging

Takeout, Bakery and Beverage Packaging

Kibble, treat & wet food packaging
The bag is built around one job: hold a steady interior while the cigars inside are carried, opened and closed again. Printed PET carries the artwork, aluminium foil does the blocking, and a PE sealant closes the three edges and anchors the zip track. A two-rib zip runs the full width of the mouth, and a peel-and-seal strip below it takes the second seal for transit. The back panel prints what a smoker reaches for on the road: twelve humidity marks from 46 to 68, a centimetre scale, an inch scale, and the barcode a retailer scans. Each bag leaves here finished: a two-way humidity pack or a pad of humidifying cotton sits behind the zip, so a buyer opens it and loads cigars. Black film, gold print, 160 x 220 mm, cut to order.
A cigar bag is a small piece of engineering that has to do three things at once: keep light off the leaf, keep water vapour from crossing the film, and survive being opened several times a day. That is why the layup is printed PET, aluminium foil, then PE sealant, in that order. The foil is the layer doing the real work. PET is there to carry the print and take the press heat without stretching, and PE is the only layer that melts, so it makes the seals and holds the zip track.
The mouth carries two closures, and they are not the same job. The two-rib zip runs the full width and is what gets opened and pressed shut again between cigars. Below it sits a peel-and-seal strip under a release liner: peel, fold the mouth over, press, and that is the seal that holds through a parcel. We print both on the same web, so the buyer gets one bag rather than a bag and a separate tape.
The back panel is where this product earns its keep at retail. Twelve humidity marks run from 46 to 68, so a hygrometer or a humidity card can be read against the bag without opening a second app. A centimetre scale sits down one edge with an inch scale beside it, because cigars are bought by length and buyers check it in the hand. Barcode and recycling mark sit at the foot of the panel, clear of the seams.
Artwork is the variable. Send the front design and the back layout, and we return a proof with the marks, the scales and the barcode position fixed, then a filled sample so the buyer judges the print on film rather than on a screen. Colour, film thickness and pack count are set per order.
| Item | Detail |
|---|---|
| Structure | Printed PET / aluminium foil / PE sealant |
| Size | 160 x 220 mm flat |
| Bag type | Flat pouch, three-side seal |
| Closure | Two-rib zip plus peel-and-seal adhesive strip |
| Black base with gold; other colourways on request | |
| Back panel | Humidity marks 46–68, cm and inch scales, barcode field |
| Insert | Two-way humidity pack or humidifying cotton, fitted |
| Packing | Flat, in cartons |
| Customisation | Size, colourway and layout to order |
On this layup the artwork prints on the outer PET, and the foil underneath stays bare. That matters for two reasons. A solid black over a mirror foil reads glossy and shows every wrinkle of the film; over PET it reads as a flat black with the gold sitting on top of it. And because the ink never touches the foil, the barrier is not broken by a print station.
Gold is a separate pass from the black. On a full-bleed black the registration shows on every edge, so the plate order is set so the gold lands last, after the black has been laid down and dried. A sheet that goes to the second pass too wet smears at the edges, which on this artwork is the first thing a buyer sees.
Seal areas are kept clear of ink. An ink film inside a heat-seal zone is a weak seal, and on a bag that gets opened repeatedly it is also where a split starts. The zip track runs through the same band, so the proof marks those margins before the plates are cut and the printer leaves them empty.
Artwork is approved flat, then a filled sample goes out. The bag a buyer judges is the printed one in the hand, not the PDF: black coverage, gold brightness and seal width all read differently on film than on a screen. That sample stays in the file, so a repeat order prints against a physical reference rather than a description.
The decoration is the product here. A full-bleed black with a gold wordmark and four gold cigar shapes tells the buyer what is inside before they read a word, and the gold is what carries the premium signal at this price point. The back is the opposite approach: near-invisible printing that only becomes useful once the bag is in use, the humidity marks and the two scales. Neither side uses a logo we do not own; the artwork is the buyer’s.
North Side Of Nanyi Road, Shiwan Town Science And Technology Park (10th Floor, Building 1, No. 13)
INQUIRY